PZEM-004T TTL Power Energy Watt Meter AC 220V 100A Electric Volt Amp PF Frequency For Arduino CT
Related Products
Arduino Mega2560 USB board
Drone
Product Description
PZEM-004T New Version TTL Power Energy Watt Meter AC 220V 100A Electricity Volt Amp Watt Kwh Voltmeter For Arduino with Coil CT
This document describes the specification of the PZEM-004T AC communication module, the module is mainly used for measuring AC voltage, current, active power, frequency, power factor and active energy, the module is without display function, the data is read through the TTL interface.
PZEM-004T-10A: Measuring Range 10A (Built-in Shunt)
PZEM-004T-100A: Measuring Range 100A (external transformer)
If you need the software, please download it via this link:
http://www.mediafire.com/file/lk5wukg2v5n5iry/004T_software%252Bdriver%252Buser_manual.zip/file
Very Important Notification:
For this product PZEM-004T, we have the update version to replace the old version. The old version has been sold out and no produce anymore. The update information as following:
1. the new version has the same size and TTL port as before
2. the software is new, we have English software as same as the PZEM-014,016, The communication protocol change to be Modbus–RTU, the display interface is changed. now it can test Voltage ,Current, Power, Power factor, Frequency and Energy 6 parameters.
3. the new version has higher precision, faster refresh speed and the more stability communication than the old version.
4. The new version increase a set for 0-10A
4. Now the product is still naked PCB, but in the future we will have the good outside case.
Now you can still use the old link to submit the order, if there is any question, welcome to contact the service to get more information.
1. Working voltage: 80 ~ 260VAC
2. Test voltage: 80 ~ 260VAC
3. Rated power: 100A/22000W
4. Operating frequency: 45-65Hz
5. Measurement accuracy: 1.0 grade
Function
Voltage
1.1.1 Measuring range:80～260V
1.1.2 Resolution: 0.1V
1.1.3 Measurement accuracy: 0.5%
1.2 Current
1.2.1 Measuring range: 0～10A(PZEM-004T-10A); 0～100A(PZEM-004T-100A)
1.2.2 Starting measure current: 0.01A(PZEM-004T-10A); 0.02A(PZEM-004T-100A)
1.2.3 Resolution: 0.001A
1.2.4 Measurement accuracy: 0.5%
1.3 Active power
1.3.1 Measuring range: 0～2.3kW(PZEM-004T-10A); 0～23kW(PZEM-004T-100A)
1.3.2 Starting measure power: 0.4W
1.3.3 Resolution: 0.1W
1.3.4 Display format:
＜1000W, it display one decimal, such as: 999.9W
≥1000W, it display only integer, such as: 1000W
1.3.5 Measurement accuracy: 0.5%
1.4 Power factor
1.4.1 Measuring range: 0.00～1.00
1.4.2 Resolution: 0.01
1.4.3 Measurement accuracy: 1%
1.5 Frequency
1.5.1 Measuring range: 45Hz～65Hz
1.5.2 Resolution: 0.1Hz
1.5.3 Measurement accuracy: 0.5%
1.6 Active energy
1.6.1 Measuring range: 0～9999.99kWh
1.6.2 Resolution: 1Wh
1.6.3 Measurement accuracy: 0.5%
1.6.4 Display format:
＜10kWh, the display unit is Wh(1kWh=1000Wh), such as: 9999Wh
≥10kWh, the display unit is kWh, such as: 9999.99kWh
1.6.5 Reset energy: use software to reset.
1.7 Over power alarm
Active power threshold can be set, when the measured active power exceeds the threshold, it can alarm
1.8 Communication interface
RS485 interface
1 Communication protocol
1.1 Physical layer protocol
Physical layer use UART to TTL communication interface
Baud rate is 9600, 8 data bits, 1 stop bit, no parity
1.2 Application layer protocol
The application layer use the Modbus-RTU protocol to communicate. At present, it only supports function codes such as 0x03 (Read Holding Register), 0x04 (Read Input Register), 0x06 (Write Single Register), 0x41 (Calibration), 0x42 (Reset energy).etc.
0x41 function code is only for internal use (address can be only 0xF8), used for factory calibration and return to factory maintenance occasions, after the function code to increase 16-bit password, the default password is 0x3721
The address range of the slave is 0x01 ~ 0xF7. The address 0x00 is used as the broadcast address, the slave does not need to reply the master. The address 0xF8 is used as the general address, this address can be only used in single-slave environment and can be used for calibration etc.operation.
1.3 Read the measurement result
The command format of the master reads the measurement result is(total of 8 bytes):
Slave Address + 0x04 + Register Address High Byte + Register Address Low Byte + Number of Registers High Byte + Number of Registers Low Byte + CRC Check High Byte + CRC Check Low Byte.
The command format of the reply from the slave is divided into two kinds:
Correct Reply: Slave Address + 0x04 + Number of Bytes + Register 1 Data High Byte + Register 1 Data Low Byte + ... + CRC Check High Byte + CRC Check Low Byte
Error Reply: Slave address + 0x84 + Abnormal code + CRC check high byte + CRC check low byte
Abnormal code analyzed as following (the same below)
l 0x01,Illegal function
l 0x02,Illegal address
l 0x03,Illegal data
l 0x04,Slave error
The register of the measurement results is arranged as the following table
Register address | Description | Resolution |
0x0000 | Voltage value | 1LSB correspond to 0.1V |
0x0001 | Current value low 16 bits | 1LSB correspond to 0.001A |
0x0002 | Current value high 16 bits | |
0x0003 | Power value low 16 bits | 1LSB correspond to 0.1W |
0x0004 | Power value high 16 bits | |
0x0005 | Energy value low 16 bits | 1LSB correspond to 1Wh |
0x0006 | Energy value high 16 bits | |
0x0007 | Frequency value | 1LSB correspond to 0.1Hz |
0x0008 | Power factor value | 1LSB correspond to 0.01 |
0x0009 | Alarm status | 0xFFFF is alarm，0x0000is not alarm |
For example, the master sends the following command (CRC check code is replaced by 0xHH and 0xLL, the same below)
0x01 + 0x04 + 0x00 + 0x00 + 0x00 + 0x0A + 0xHH + 0xLL
Indicates that the master needs to read 10 registers with slave address 0x01 and the start address of the register is 0x0000
The correct reply from the slave is as following:
0x01 + 0x04 + 0x14 + 0x08 + 0x98 + 0x03 + 0xE8+0x00 + 0x00 +0x08 + 0x98+ 0x00 + 0x00 + 0x00 + 0x00 + 0x00 + 0x00 + 0x01 + 0xF4 + 0x00 + 0x64 + 0x00 + 0x00 + 0xHH + 0xLL
The above data shows
l Voltage is 0x0898, converted to decimal is 2200, display 220.0V
l Current is 0x000003E8, converted to decimal is 1000, display 1.000A
l Power is 0x00000898, converted to decimal is 2200, display 220.0W
l Energy is 0x00000000, converted to decimal is 0, display 0Wh
l Frequency is 0x01F4, converted to decimal is 500, display 50.0Hz
l Power factor is 0x0064, converted to decimal is 100, display 1.00
l Alarm status is 0x0000, indicates that the current power is lower than the alarm power threshold
100% new brand high quality
1 x PZEM-004T AC Voltmeter Ammeter
1 x Coil CT
When you order from opencartworks.com, you will receive a confirmation email. Once your order is shipped, you will be emailed the tracking information for your order's shipment. You can choose your preferred shipping method on the Order Information page during the checkout process.
The total time it takes to receive your order is shown below:
The total delivery time is calculated from the time your order is placed until the time it is delivered to you. Total delivery time is broken down into processing time and shipping time.
Processing time: The time it takes to prepare your item(s) to ship from our warehouse. This includes preparing your items, performing quality checks, and packing for shipment.
Shipping time: The time for your item(s) to tarvel from our warehouse to your destination.
Shipping from your local warehouse is significantly faster. Some charges may apply.
In addition, the transit time depends on where you're located and where your package comes from. If you want to know more information, please contact the customer service. We will settle your problem as soon as possible. Enjoy shopping!
Related Products
Arduino Mega2560 USB board